safety levers break, mag releases go bad, disconnectors hang, and the list goes on.
There's an up side... Cheap, and can last a looooong time if you don't shoot much.
And this.
safety levers break, mag releases go bad, disconnectors hang, and the list goes on.
There's an up side... Cheap, and can last a looooong time if you don't shoot much.
No. Never.
When you use the MIM parts and trim everything square to the axis of the pins (believe it when I say so many are not) you take away some of the hardened surface. Tjis shortens the life of the parts considerably. It is much better than original but it is still Mooshy compared to the tooled steel pieces.
I will consider doing an MIM clean up for some friends but do not recommend it.
You know you want to do it. Just do it. You'll feel better!
It would be possible for the MIM parts used by some makers to be very high quality, but that would cost more. MIM isn't necessarily lesser quality or utility than machined tool steels, but what we see in most commercial 1911s isn't very good as you noted.
I got lucky with a Kimber that had a very nice trigger with the original MIM parts for about 25K rounds. Then the hammer followed. On the other hand, other guns have not yielded the same success.
You need a really good heat treatment for MIM parts to be just good parts and that doesn't always happen.
No. Never.
25K is a really good number.
As mentioned when I cut everything square to the pin axis some of the hardening is removed. This shortens the round count
Yep, same thing happens with stock AR hammers. I don't know about now, but in the 90s the surface hardening on most was very shallow. It didn't take too many swipes on the stone to get to soft metal in some cases.
And then the "Mooshy" trigger.
On the upside, a Glock user might be more comfortable with a mushy trigger
Hah! God carries a 1911 --- Sponge Bob carries a Glock!
They really do put a nice 1911 together. The one I was referring to above is a CZ 1911A1 built by Dan Wesson. The build quality is the same as my DW CCO except for a minor cosmetic bit on the extractor finish. I'm hoping to add a full size stainless Valor to the family next spring.
It was probably already said in this thread. But I'm asking anyway. What's the beef with MIM parts?
Probably because God doesn't need his gun to work....Hah! God carries a 1911 --- Sponge Bob carries a Glock!
Probably because God doesn't need his gun to work....
I got lucky with a Kimber
Agree with this. So many mention unreliability despite 70 plus years of service. Granted, part is because is takes the military forever to change and adapt anything new, i.e. look at the M16\M4. But, actually if well maintained, they run like a top. Delta Force used them forever, despite the rest of the military going to the M9. And they could pick their own. Other special units as well have them too. Granted last unit just stopped issuing in favor of the Glock, but 105 years of service, seriously think about that and how much everything else in the military has changed. Must absolutely be a reason why they were using them, even recently in the sandbox.Darn people figured it out!! The United States issued a 100% unreliable pistol to our Armed Forces for 70 years?!?!!? Where was Gaston with his magical Tupperware when we needed him???
Agree with this. So many mention unreliability despite 70 plus years of service. Granted, part is because is takes the military forever to change and adapt anything new, i.e. look at the M16\M4. But, actually if well maintained, they run like a top. Delta Force used them forever, despite the rest of the military going to the M9. And they could pick their own. Other special units as well have them too. Granted last unit just stopped issuing in favor of the Glock, but 105 years of service, seriously think about that and how much everything else in the military has changed. Must absolutely be a reason why they were using them, even recently in the sandbox.
Agree with this. So many mention unreliability despite 70 plus years of service. Granted, part is because is takes the military forever to change and adapt anything new, i.e. look at the M16\M4. But, actually if well maintained, they run like a top. Delta Force used them forever, despite the rest of the military going to the M9. And they could pick their own. Other special units as well have them too. Granted last unit just stopped issuing in favor of the Glock, but 105 years of service, seriously think about that and how much everything else in the military has changed. Must absolutely be a reason why they were using them, even recently in the sandbox.
Delta Force Larry Vickers, who carried the 1911 in the service, and is a die hard 1911 guy, only recommends the Wilson Combat if you want to carry a 1911. If not a Wilson, he recommends a Glock 19.
He also says the 1911 is more for an experienced gunsmith. If you don't have the money, or even the time, to maintain the 1911, then it's not for you.
If a die hard 1911 guy says that, you can't help but pay attention.
He might have a tie with Wilson.....
Maybe. I did see him sitting in the Wilson booth at the NRA show.
I do think Wilson makes a nice gun. Only failures I have had with mine was ammo related. Not the guns fault that I seated a primer backwards or Federal didn't put enough powder in a cartridge. I did have some issues with it not wanting to lock back on an empty magazine. Not an uncommon problem with other guns as well. Wilson tweaked something and had the gun back to me quick.